found everything locally that i needed.
THANKS FOR ALL THE HELP!!
keith
Search found 11 matches
- Wed Dec 30, 2015 12:15 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
- Mon Dec 28, 2015 2:51 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
Re: tooth pattern
rechecked everything without crush sleeve, looks the same, just need new outer bearing and race, seal, crush sleeve and nut. if you could give me a price on them I will send you a cashiers check.
thanks,keith
thanks,keith
- Fri Dec 25, 2015 6:36 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
Re: tooth pattern
since it's back apart again i'm going to check everything again with the new inner bearing before I put a new crush sleeve in. the outer bearing has been such a tight fir that I've had to heat it each time I take the pinion out,(rear diff to hard to put in my press by myself) that i'm going to repla...
- Thu Dec 24, 2015 4:10 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
Re: tooth pattern
well I just found out that pinion bearing pre-load is a lot more touchier with the crush sleeve, went from less than 10inlb. to 40inlb. in less than 1/8 of a turn!, sooo what do I need to do? just new crush washer or outer bearing also? #$_&%!
keith
keith
- Wed Dec 23, 2015 10:56 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
Re: tooth pattern
what effect does the backlash have on the pattern?
keith
keith
- Wed Dec 23, 2015 9:47 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
Re: tooth pattern
yes, it has been quite an adventure. I really noticed how the flat line at the bottom pretty much went away, and the very thin line across the top. and how the the pattern widened out. setting the backlash was tedious trying to get it as close as possible. i'll post a pick after final assembly. than...
- Mon Dec 21, 2015 7:36 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
Re: tooth pattern
ok, today i got this with .041 pinion shim
.080-.010 backlash
keith
.080-.010 backlash
keith
- Mon Dec 21, 2015 1:19 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
Re: tooth pattern
had it at 038 and was riding on top edge, will try about 045 and get backlash to 010
keith
keith
- Sun Dec 20, 2015 5:22 pm
- Forum: 10 Bolt Differential Questions
- Topic: tooth pattern
- Replies: 16
- Views: 28976
tooth pattern
8) 20151220_142606_resized.jpg 20151220_131815_resized.jpg You're right, a real lesson in patience! this is what i started with, 8.5 rear, eaton posi, richmond 3.23 ring and pinion, install kit from JDRACE. old pinion inner bearing honed out with 052 shim,preload of 14in.lb. 244 pass. side carrier s...
- Fri Dec 11, 2015 11:02 am
- Forum: 10 Bolt Differential Questions
- Topic: set up specs
- Replies: 4
- Views: 10091
Re: set up specs
did a bunch of research before your reply and a company called AAM has a page that states on a 2cut the tooth height is the same on toe and heel, and on a 5cut the toe height is shorter than the heel.
thanks, keith
thanks, keith
- Thu Dec 10, 2015 11:35 am
- Forum: 10 Bolt Differential Questions
- Topic: set up specs
- Replies: 4
- Views: 10091
set up specs
in the usa standard gear set-up booklet under diff. set up it has old 5 cut/ new 2 cut for gm 8.5&8.6, how do you tell the difference? different back lash settings
thanks
thanks