www.jdrace.com

wELL A CAGE IS THE BEST WAY TO KEEP IT FROM TWISTING. the CAR SHOULD NOT TWIST IF YOU ARE STREET BouND. My kid races hers ...BUT it is 2.56 gears with a V8 270hp Boat motor from the summit racing scratch and dent table...LOL. Really it was a 500.00 long block sbc motor. 14.50 et 1/4 mile with 2.56 g...

Gears, My race car is only 3.73 gears and run those numbers.. and pull the fronts.... BUT REMEMBER...my car is a RACE car ONLY. Does not go on the street. BRAKES- think your a little mixed up on that stuff too. THe BACKING PLATES must be used from 1977 - 1980 9.5x2 drum system the 75 76 did have 9.5...

Moser axles on Ebay -
By the way everything at MOSER just increased in price AGAIN this year.
comes with new metric studs like s10


https://www.ebay.com/itm/265827869700

Well strip is where you will be at a disadvantage... WHAT are you expecting to do? How often? The build: 4.10 is better than 4.11 as even GM has realized that as they do not use that ratio anymore. 4.11 is 9 - 37 4.10 is 10 and 41 MORE teeth give you more touch point and bleed the heat off better so...

Yah likely the seal is just dried out :( PReload - yes normally the correct preload is with a NEW crush sleeve and the posi or open carrier removed when figuring. IN THIS case... You should be safe with replacing the seal with some RTV on the outside diameter of the seal to the inside diameter of th...

RING AND PINION about .008 - .010 NO MORE could be slightly less BUT doubt it if it has any kind of mileage.

Not much as options. You will need a donor rear end for brackets - 12 bolt chevy we use the camaro Moser center for the torque arm connection and then have to weld on the brackets from the donor rear to your NEW Moser housing 12 bolt rear...Same with Ford 9" or any other aftermarket set-up. We ...

Yep, remove the 8 bolts which are right hand normal thread...leave 2 across from each other and just back those to bolts little by little so they do not snap from the preload force when removing them.... ren=move them each equal amount back and forth across from each other. now take pictures of the ...

Jason, Glad to see you found us... We have done many of these conversions. The trouble is TIME... The longer you wait the harder it gets to find stock parts...Seems the whole world is killing all older scrap yards. So find a literally THROW AWAY H body car is TOUGH....lol. the strongest way to make ...

1976 STAR FIRE 3.8 LITER BUICK V6 WITH TRANSMISSION MANUAL 4 SPEED.

53K MILES ON MOTOR AND TRANSMISSION

THEY ARE A MATCH SET
MOTOR RUNS
TRANSMISSION MOVES THE CAR AS PICTURED IN THE VIDEO PROVIDED.

VIDEO OF MOTOR AND TRANS WORKING YOU TUBE
LINK:
https://www.youtube.com/watch?v=qS6usEQBK7A

oh boy - That will be a tough one.

IF anyone does have this they can bring it to JD race location and I will remove the brackets for him...
Best I can do to help - wll keep an eye out here at swap meets.
DO you have any pics to help us and them ID a 49 50 9.3 bracket rear end.
Jim
JD race

I is good that we are still trying to be inventive. SEEMS the government is just working LAZY into every newer generation. WE can not be LAZY and be satisfied with what is tossed to us. We have to want more and we have to create if somethings are not available. It must stay this way as this is how o...

That is VERY interesting. I am glad we could supply your need for the gear. It is truly neat how just about anyone with some skill can get machining done to create and solve a problem . How did you know the gear mesh would work as far as pinion engagement to the ring being the same as GM engagement?

No, They have been discontinued for many years.
You will need to find a USED 2 series or 3 series unit to part out.
we have 2 series unit complete used for 250.00 each
Jim
JD Race

Ok if you have anything else send some pics will try to help.
Jim